Accessories

All prices displayed on these pages are exclusive of 19% VAT which is automatically added for all European Union customers during checkout!

!

PS2 Keypad
!
hw

PS/2 Keypad compatible with microHAM products
Suitable for:
micro KEYER, micro KEYER II, MK2R, MK2R+, CW KEYER, STATION MASTER

  • powered from attached device
  • allows access to nine message memories
  • record and playback CW/Voice memories
  • control contest serial number insertion
  • chain/loop messages with variable delay
  • set/change CW speed
  • set antenna
  • set antenna split
  • control SteppIR
  • control rotator azimuth
  • many more ...

iLINK - SteppIR
!

Cable connecting MKII iLINK port and SteppIR native control DATA OUT port.

Please note, MKII is now compatible with new SDA100 controller as well as Ultra Beam controller.

ACC - Dual SteppIR
!

Cable connecting MK2R(+) ACC port and two SteppIR's controllers using native control DATA OUT port.

Please note, MKII is now compatible with new SDA100 controller as well as Ultra Beam controller.

Paddle Debouncer
!
Picture 009

 

It appears that some of the new paddle designs have abandoned the time tested coin silver contacts and are using "improved" alloys in an attempt to avoid problems with oxidation.   While those alloys and/or surface treatments seem to be reliable when used in circuits with a high threshold separating "key up" and "key down" states, the new contacts are a problem with PIC based keyers like WinKey that use a voltage divider and single input pin to sense both the "dit" and "dah" paddle closure.
 
These new alloys appear to create a semiconductor contact rather than a purely conductive one.  In trying to discover and fix the problems with a few of the newer paddle designs and WinKey, it appears that the voltage drop across the paddle contacts is essentially independent of the current through the contacts.  In one test, the divider resistors in the WinKey input network were scaled by a factor of 10 in an attempt to make contact resistance a smaller part of overall circuit resistance ... with absolutely no difference in behavior!  This surprising response is exactly what would be predicted if the contacts were acting like a forward biased diode.
 
To accommodate these new paddle designs, K1EL and microHAM have cooperated to produce a "paddle processor/debouncer."  The debouncer uses a micropower PIC with independent, high threshold inputs to sense the paddle state.  Paddle closures are processed with an advanced debouncing algorithm to remove all "noise" on the inputs and passed on to the keyer as unambiguous levels. 
 
The debouncer consumes less than 1 mA in operation and about 1 uA in sleep mode.  It will operate for several years on the internal "coin" battery without the need for a power switch.        
 
The debouncer is available in two versions.  Both versions have 20 cm output cables terminated in a standard 1/4" stereo plug to connector to microKEYER or CW Keyer.  The Begali version has a one meter long input cable which terminates in a 3.5 mm (1/8") stereo plug which will connect directly to the paddles.  The generic version replaces the 3.5 mm plug with a 1/4" stereo jack.
 
Suitable for:
old micro KEYER and old CW KEYER
Note: CW Keyers manufactured in 2008 has Debouncer already integrated
 

Still available accessories for discontinued Band Decoder
!

RELAY BOARD
!
Optional output board for micro BAND DECODER

PCCOM1 cable adapter
!
Cable for micro BAND DECODER and computer COM port

RIG232 cable adapter
!
Cable for micro BAND DECODER and TS-570, 480, 870, 2000, FT-1000MP xxx or any other transceiver with DB9 male computer port
Note: Do not use this cable for Elecraft K2 !!!

RIG232X cable adapter
!
Cable for micro BAND DECODER and FT-847

PCLPT1 cable adapter
!
Cable for micro BAND DECODER and computer LPT port

IC1 cable adapter
!
Cable for micro BAND DECODER and Icom's transceivers

IC2 cable adapter
!
Adapter for micro BAND DECODER PTT and Icom's AUX1 connector

TS1 cable adapter
!
Cable for micro BAND DECODER and Kenwood's transceivers

TS2 cable adapter
!
Adapter for micro BAND DECODER PTT and Kenwood's REMOTE connector

FT1 cable adapter
!
Cable for micro BAND DECODER and Yaesu's BAND DATA, DIN8 connector

FT2 cable adapter
!
Cable for micro BAND DECODER and Yaesu's BAND DATA MINIDIN8 connector

FT3 cable adapter
!
Cable for micro BAND DECODER and Yaesu's CAT MINIDIN8 connector

FT4 cable adapter
!
Cable for micro BAND DECODER and Yaesu's CAT DIN6 connector

FT5 cable adapter
!
Cable for micro BAND DECODER and Yaesu's CAT MINIDIN6 connector

PAYAESU1 adapter
!
Adapter for micro BAND DECODER and Yaesu's automatic amplifiers FL-7000, VL-1000
Note: For FL-7000 original cable ended with DIN8 plug is still necessary

PAICKL1 adapter
!
Adapter for micro BAND DECODER and Icom's automatic amplifiers IC-2KL, IC-4KL
Note: For IC-2KL original cable ended with DIN7 plug is still necessary

PAICPW1 adapter
!
Adapter for micro BAND DECODER and Icom's automatic amplifiers IC-PW1

PASTEPPIR adapter
!
Adapter for micro BAND DECODER and SteppIR antenna controller

BPF-M600
!
Adapter for micro BAND DECODER and Dunestar M600 band pass filters

BPF-FM6
!
Adapter for micro BAND DECODER and FM6 BPF matrix

BPF-419
!
Adapter for micro BAND DECODER and ICE-419/A band pass filters