; firmware for ARCO, change log
; by Jan Waclawek, microHAM
--------------------------------------------------------------------------------

v3.2.B, released 221215
  - fixed minor issue with pulse sensors stopped counting when
    Calibration menu exited while rotator is turning
v3.2.A, released 221208
  - fix to retain M-TURN POT calibration upon firmware update
v3.1.H, released 221202
  - fixed ARXC.MAG primary sensor calibration incorrect display
  - startup azimuth display improvement
v3.1.F, released 221121
  - improved M-TURN POT readout
v3.1.E, released 221027
  - support for MODBUS/OMRON Q2V added
v3.1.D, released 221020
  - overlap zone end-edge indication added
  - overlap reversal by tapping on overlap icon added
v3.1.C, released 221017
  - custom map option added
  - overlap zones indication added
  - ARXC.REL-controlled antennas handling improved
v3.1.B, released 220929
  - support for ARXC.MAG board added
  - minimum touch duration parameter added
  - fixed day/night background color change on main screen
v3.0.A, released 220601
  - support for ARXC relay boards added
v2.1.C, released 220314
  - fixed spurious false overtemperature message
v2.1.B, released 220222
  - vnc server implemented
v2.0.C, released 220111
  - touch responsivity setting added to System menu
v2.0.A, released 211220
  - 3dB beamwidth added, adjustable per antenna
  - antennas setup in separate submenu (Heading-Antennas)
  - time is displayed in screensaver
  - improved mains hum suppression for Pot/Multiturn Pot
  - in Heading-Calibration menu, Sensor Position indicates
    unadjusted position for resistive sensors
  - adjustable minimum backlight in System menu
  - MAC address displayed in LAN menu
v1.4.A, released 211022
  - added Moon position calculation/display
  - improved remote control through Link (control via buttons,
    transfer of presets, status)
  - improved automatic aspects of Link functionality (Sync/Align,
    Tower, Rotating Tower, indicators)
  - motor current is now displayed also in menu Heading tab
  - LP/SP implemented in keyboard view
  - QRB displayed when entering locator in keyboard view
  - QRB displayed in status when touch'n'turn used
  - improved decision when to redraw maps
  - added 18V to voltages selection, corrected actual DC output voltages
  - changed default voltage for Prosistel rotators
  - added HyGain CD-44 and AR-40
  - implemented highlight of last used preset
  - implemented LAN remote control password, and DNS for Client
v1.3.A, released 210908
  - test version
v1.2.A, released 210823
  - fixed incorrect automin for AC rotators
  - fixed buttons rampdown to be proportional to rampup for AC rotators
  - brake/PSU off is delayed by 5 sec after last movement
  - hold delay range expanded down to 0.1 sec
  - new option BUTTON USE RAMPS (in Menu->General) - if unchecked, buttons
    use CALIB SPEED set in Menu->Heading
  - after update load, last window asks for switching ARCO OFF/ON
v1.1.C, released 210817
  - correctly rounded azimuths returned through control protocols
  - fault DOES NOT MOVE renamed to NO MOVEMENT
  - G-450C (ADC/CDC) renamed to G-450DC(A/CDC)
  - G-650C and G-450C set correctly to AC with RHEO
  - green LED for Motor now lits also when buttons used in Menu->Heading
v1.1.B, released 210811
  - on Rotator->Settings, when Model is not Custom, now it is possible to
    change SensorType, SensorValue and TotalRotation - all these cause warning
    when changed, and if set to non-default, they are highlighed by red
  - removed YAESU-G450CDC, YAESU-G450ADC renamed to YAESU-G450C (A/CDC)
v1.1.A, released 210810
  - Prosistel rotators with potentiometer use the new M-TURN POT option
  - fixed problem with detecting endswitches for Create rotators
  - default pot value for Create rotators changed from 1k to 5k