; sml, firmware for STATION MASTER (SM), change log
; by Jan Waclawek, microHAM
--------------------------------------------------------------------------------

v2.39, released 191111
  - bug fixed: Responses to commands MD0 and MD1 from FTdx101D was interpreted
    incorrectly.
v2.38, released 190610
  - IC-9700 and FTdx101D added to the list
v2.37, released 190301
  - TS-890 added to the list
v2.36, released 180104
  - IC-7610, IC-821H added to the list
v2.35, released 170309
  - bug fixed: Control of SteppIR(SDA100,10/20kHz) didn't work
v2.34, released 170302
  - SteppIR and UltraBeam devices (now collectively referred as MotorANT devices)
    are now categorized by range and type instead of model name.
  - support for UltraBeam RCU-06
  - tuning of UltraBeam initiated at 10kHz boundaries
  - tuning of SteppIR with SDA 100 controller initiated at 50kHz boundaries and
    optionally at 10kHz or 20kHz boundaries (band dependent)
v2.33, released 161212
  - some SDRs added to the list:
    - Flex 6000 series (uses TS-990 protocol)
    - Flex 5000 (uses TS-2000 protocol)
    - Apache Labs ANAN 100/200 (uses TS-2000 protocol)
  - Now PTT is not locked when TX frequency is out of SteppIR range upon startup
v2.32, released 161103
  - bug fixed: Automatically reported operating frequency was ignored
      on Icoms with new firmware (when CI-V transceive was set to on):
      IC-7100(fw v1.10(E4)+), IC-7300, IC-7600(fw v2.00+), IC-7700(fw v2.10+),
      IC-7800(fw v3.10+), IC-7850, IC-7851
v2.31, released 161004
  - Expert Electronics MB1 added to the list
v2.30, released 160419
  - support for newer firmware versions of some ICOMs:
      Icom IC-7100, fw v1.10(E4)+
      Icom IC-7600, fw v2.00+
      Icom IC-7700, fw v2.10+
v2.29, released 160415
  - iLink coupling to SMORF
  - possibility to set software lock from router
  - FT-991, IC-7850, IC-7851, IC-7800 fw v3.10+, IC-7300 added to the list
  - fixed FT-900, FT-890, FT-840
v2.27, released 140114
  - Hilberling PT8000 added to the list
  - Elecraft K3 protocol updated to Rev.E11 and extended by P3 protocol Rev.A4
v2.26, released 131204
  - FTdx1200 added to list
v2.25, released 130815
  - IC-7100 added to list
v2.24, released 130513
  - adopted UltraBeam v1.36 protocol change
v2.23, released 130506
  - bug fixed: commands SB,DV was mistakenly included to K2 protocol
  - bug fixed: SteppIR/SDA100 Remote Driver bit treated as "HAM mode"
v2.22, released 130417
  - added new radios to CAT, see Keyers changelog
v2.20, released 120911
  - added support for new UltraBeam models
v2.19, released 120727
  - control commands protocol extensions implemented
  - added delays in Acom2000 communication protocol (confirmed with manufacturer)
v2.17, released 120214
  - SteppIR/UltraBeam front panel settings for 180/bidir are retained
  - for UltraBeam, tuning step changed to 25kHz
v2.16, released 111202
  - fixed problem with SDA100/BigIR
v2.14, released 110809
  - fixed permanent BUSY if both switch delay and break-before-make are set to 0
  - improved CAT decoding upon powerup
  - added ALARM_ROTA_NEGATIVE for negative input to the rotator sensor
  - bug fixed in IF command in Kenwood protocol
  - multiple minor bug fixes
v2.8, released 100202
  - UltraBeam 180/bidir support added
v2.7, released 100120
  - UltraBeam support added
v2.6, released 091222
  - SteppIR SDA100 support added
  - AUX baudrate setting bug fixed
  - KeyOut tail added
v2.2, released 081217
  - SteppIR control enhancements
  - added Acom2000A PA control
v2.0, released 081113
  - standalone CAT decoding
  - new format of configuration data
  - steppir protocol enhancements, version reported to router
  - if available, yagi steppir bidir/180 turn used for [LP]
  - added optional KeyIn inverting
  - added break-before-make delay for ANT and BPF relays
  - added always active rotator control option
  - added PA standby and keep PA off options to FUNC menu
  - PS/2 keypad is now fully configurable and individualkeys can be forwarded to Keyer
  - added CIV option on auxiliary serial port
  - added CAT input on auxiliary serial port (BandDecoder-like functionality)
  - brake release after 15s idle during braked rotator calibration
v1.3, released 080723
  - fixed inverted BCD outputs
v1.2, released 080722
  - fixed bug when inhibit lead = 0
  - added alarms for KeyIn late or drop
  - fixed KeyOut
  - added SINK state for A/B voltage measurement
  - fix for iLink coupling/uncoupling
v1.1, released 080702
  - added noTxAntenna lock to Keyer via I2C
  - sleep mode command from keyer is accepted
v1.0, released 080624
  - First release of SM firmware.