; uconf, microHAM device configurator, change log ; by Martin Bujdak, microHAM -------------------------------------------------------------------------------- v5.9, released 180130 - fix: Some unsupported radios was mistakenly included to the list. v5.8, released 160818 (private release) - Support for uSM v3.3 - DXE-PS-3B STACK added to the list - minor bugs fixed - Released with uSM v3.3, uBD v5.3 v5.7, released 150205 (private release) - Support for uSM v3.2 - New stack switches added to the list: - DXE PRO-STACK - 2x DXE PRO-STACK in cascade for 3 antennas - 3x DXE PRO-STACK in cascade for 4 antennas - Released with uSM v3.2, uBD v5.3 - Compiled with gcc 4.8.1, wxWidgets 3.0.0. v5.6, released 120817 (private release) - Released with uSM v3.1, uBD v5.3 - Compiled with gcc 4.4.1, wxWidgets 2.9.3. v5.5, released 100831 (final official release) - bug fixed: When ORION II was selected as band data source for Band Decoder baud rate could be set incorrectly. - Compiled with gcc 4.4.1, wxWidgets 2.8.9. v5.4, released 081211 - No features added, just compiled with new compiler version: gcc 3.4.5, wxWidgets 2.8.9 v5.3, released 080213 - Support for Hercules and Ameritron amplifiers (uBD v5.3) v5.2, released 080212 - Radios IC-760 Pro, IC-780 added to the list. - Internal: IC-275E protocol code unified with general Icom protocol code. v5.1, released 071008 - Support for uBD v5.1 - New rigs: FT-950, FTdx9000 Contest - FT-450 has new internal code - BD feature "stop polling, use autoinformation" can be enabled for all radio types now. - "Yaesu xxx (BAND DATA)" items removed from the list of band data sources. Use "PC (LPT port) or Yaesu BAND DATA" instead of them. v5.0, released 070921 - Support for uSM v3.0 - New antenna switches added to the list: - Comtek Stack Yagi System STACK-2 - Comtek Phased Vertical System PVS-2 - Comtek Antenna Switch System RCAS-8 - Support for uBD v5.0 - New rig types added to the list: - JRC JST-145/245 - Ten-Tec OMNI VII, ORION II - Icom IC-275E - Yaesu FT-2000, FT-450, IC-7000 - Wider range of serial ports (COM1-COM30). - bug fixed: Previous version allowed read/write configuration to device of different type. v4.2, released 070316 - minor changes (mutex uconfIsRunning) v4.1, released 060612 - Support for uBD v4.5 that allows to connect new rig type: Yaesu FTdx9000. - Support for uSM v2.7: - New stack switches added to the list: - 4 ANTENNA SWITCH (general) - Comtek Stack Yagi System SYS-3 - Released with new firmware: uBD v4.5, uSM v2.7 - Using of exceptions was refused due to bug in compiler. It caused an unexpected errors under some circumstances. v4.0, released 050929 - Configurator waits longer for answer to configuration packet. This allows newer devices with processor AT89C51ED2 (bootloader v3.0) to write configu- ration to EEPROM without error message. - New stack switches added to the list of devices supported by STACK MAX: - N4TZ STACK DESIGN - OM2KW STACK It requires firmware version at least uSM v2.6. - Migration to gcc 3.4.2, wxWidgets 2.6.0 v3.4, released 050801 - Added support for new band decoder firmware uBD v4.4 that allows to use 4 positional external switch. v3.3, released 050603 - Added support for Barrett 900 transceiver serie. v3.2, released 041228 - New stack switches added to the list of devices supported by STACK MAX: - micro STACK SWITCH QRO 3 ANT - micro STACK SWITCH QRO 2 ANT It requires firmware version at least uSM v2.4. - Released with new firmware: uBD v4.2, uSM v2.4 - Released with pdf documentation of antenna switches. v3.1, released 040805 - Support for uBD v4.1 (hot switch protection, auto answer mode for Icoms and Kenwoods, accept frequency from logging software). - Corrected default rig interface for Yaesu FT-920. - Support for uSM v2.3 (posibility to disable main radio feed to some antennas) v3.0, released 040408 - Support for uBD v4.0 that allows to connect Yaesu FT-757. - Some flags (just_read, just_written) added to cfg file. v2.2, released 040308 - Fixed bug. Configuration parameter "cfg_flags_2" was not correctly readed from micro STACK MAX. - Note: Since this version it is distributed with remote controller. v2.1, released 040226 - Default configuration for micro STACK MAX with micro STACK SWITCH has disabled any BOP combination. - Compatibility with uBD v1.8/v1.9 was disclaimed. To upgrade these versions of band decoder firmware it is needed to use some of previous versions of configurator. v2.0, released 040124 - Support for uBD v3.1 that allows to specify the number of protected stations if the same band protection is selected. Also Icom address autodetection checkbox was added. - Support for uSM v2.0. It allows to specify the strings displayed on info panel. Also some vertical arrays was added to the list. - Split buttons on the page "Output" was replaced by more comprehensible radio buttons. - Current configurations are stored at exit and loaded at program start. v1.6, released 031105 - Fixed communication bug of previous version. v1.5, released 031105 - Support for uBD v3.0 that allows to connect some new rig types: Ten-Tec ORION, JUPITER, ARGONAUT V. - Also some other rigs added to the list: Yaesu FT-840, Elecraft K2. v1.4, released 031006 - Support for uBD v2.4 that allows to connect some new rig types: Ten-Tec DELTA II, Yaesu FT-900, FT-920, FT-990. - Added micro DOUBLE TEN SWITCH to the list. v1.3, released 030819 - Support for uBD v2.1. It contains new option on multifunctional pin, generation of pulse when band, antenna port or frequency is changed. Also new band on 60m was added. - Possibility to upgrade uBD v1.8/v1.9 although LPT band data source and second serial port are used. - Some modifications to speed up communication when bootloader is active instead of application. v1.2, released 030804 - Support for bootloader v2.0, that include possibility to load EEPROM from firmware file, test compatibility of firmware file with device. - Test compatibility of configuration with device. - This version is much more tolerant against communication problems with band decoder firmwares from v1.7 to v1.9. - Added support for new features in band decoder firmware: - the same band protection on multifunctional output (since uBD v1.9) - get band data from ACC instead of CAT, if they are valid (since uBD v2.0) This allows combine manual/PC (via ACC) switching with automatic (CAT) switching. v1.1, released 030613 - Default state of both, AUX and BOP, is disabled for WX0B stack controlers. - Now program saves its configuration to registry. - uSM bug fixed: Corrected some constants used for BOP and AUX on WX0B stacks. - Added support for multifunctional output (new feature since uBD v1.8). Page "PW1" in advanced settings dialog was replaced by page "special" with controls that allows configurate multifunctional output. Now it supports IC-PW1, IC-2KL/4KL and micro SELECTOR control. - Serial port read timeout was icreased to 2000 ms. This avoids errors when RS232 is realized via USB. v1.0, released 030513 - This is the first release of microHAM universal device configurator. It replaces previous "uBD Configurator 1.4" and is intended to support all configurable microHAM devices. Now it can configurate following devices: - micro BAND DECODER (up to v1.7) - micro STACK MAX (v1.0)